Differential Ring Pinion Gears 3.69, 3.9, 4.08, 4.36 R200 Final Drive, Performance OEM and Aftermarket Engineered Parts Global Leader In 300ZX 350Z 370Z G35 G37 Q50 Q60 - Z1 Motorsports
place
expand_more
close
check_circle_outline Added to Cart
Differential Ring Pinion Gears 3.69, 3.9, 4.08, 4.36 R200 Final Drive
shopping_cartCart
payment

Checkout

Discover More Products

Z1 Motorsports High Capacity Differential Cover Kit
Z1 Motorsports High Capacity Differential Cover Kit
$198
OEM Differential Pinion Crush Sleeve
OEM Differential Pinion Crush Sleeve
$14.33
OEM Differential Pinion Outer Bearing
OEM Differential Pinion Outer Bearing
$47.50
OEM Differential Pinion Inner Bearing
OEM Differential Pinion Inner Bearing
$88.07
OEM Differential Front Seal (Pinion Seal)
OEM Differential Front Seal (Pinion Seal)
$14
Z1 350Z / G35 Heavy Duty Short LSD Output Shaft
Z1 350Z / G35 Heavy Duty Short LSD Output Shaft
$138
close

Differential Ring Pinion Gears 3.69, 3.9, 4.08, 4.36 R200 Final Drive

Brand: Nissan
Fits models: 350Z / 370Z / G35 / G37 / FX35 / FX45

Product Description

For those of you looking for increased performance off the line we now offer this Nissan OEM final drive ring and pinion gear set.  These gears will fit 03+ model differentials, manual transmission model cars only, and will increase acceleration.  This of course comes at a trade off of higher cruise speed RPM and decreased fuel mileage.

We offer an installation kit that contains all new Nissan OEM bearings and seals. We highly recommend the purchase and use of this install kit.  Please note that installing a ring and pinion requires precision setting of the bearing pre-load and clearances to complete the job. When installing be sure to keep the factory shims in their respective locations. Shims should not need to be changed.

Included in the Bearing and Seal Kit:

  • 2 X Nissan OEM Differential Side Carrier Bearings
  • 2 X Nissan OEM Differential Side Oil Seals
  • 1 X Nissan OEM Inner "Back" Pinion Gear Bearing
  • 1 X Nissan OEM Pinion Crush Sleeve
  • 1 X Nissan OEM Outer "Front" Pinion Gear Bearing
  • 1 X Nissan OEM Pinion Oil Seal
  • 1 X Permatex Ultra Gray Gasket Maker

It is highly recommended that an experienced mechanic install this ring and pinion gear set as excessive noise or even catastrophic failure can result from improper installation.  If you would like to have your gear set installed at Z1, please contact us at [email protected] for an installed price.

Please choose the appropriate options below including our Full OEM Differential Bearings and Seals Kit for all the additional parts you'll need to complete the install.  

If you are unsure of your current gear ratio, please take a look at the Gear Ratio Chart found HERE.

*** This item does not qualify for any additional discounts or promotions ***

Available Options:

Please review the product description if you are unsure about any of the options below.

Include:

Gear Ratio:

Quantity:

Price: $638.00
add_shopping_cart Add to Cart
commentLeave a Review question_answerAsk A Question About This Product

Customers who bought this item also purchased ...

Z1 Motorsports High Capacity Differential Cover Kit
Z1 Motorsports High Capacity Differential Cover Kit
$198
OEM Differential Pinion Crush Sleeve
OEM Differential Pinion Crush Sleeve
$14.33
OEM Differential Pinion Outer Bearing
OEM Differential Pinion Outer Bearing
$47.50
OEM Differential Pinion Inner Bearing
OEM Differential Pinion Inner Bearing
$88.07
OEM Differential Front Seal (Pinion Seal)
OEM Differential Front Seal (Pinion Seal)
$14
Z1 350Z / G35 Heavy Duty Short LSD Output Shaft
Z1 350Z / G35 Heavy Duty Short LSD Output Shaft
$138

Questions our customers have asked

Just confirming this will go straight into manual diff and what would the cost of shipping be to Australia? Also could i please have the part numbers for install kit? E.g bearings, shims and seals etc
Yes these gear ratios will fit the manual differential carrier. We use OEM replacement parts for the install kit.
Hi, i would like to know if these gears are compatible with AT Differential Carriers, 2010. Thanks Rej
The LSD/carrier has a .4" difference in offset. You can use the cast iron housing but you will need a "manual" LSD. Depending on vehicle we may also need to confirm the companion flange style? 3 bolt Quibo coupling or 4 bolt companion flange?
Will this upgrade need the limited slip differential replacement also or the gear change itself will work with the stock of my 2005 automatic 350 Z
You will need a "Manual" Differential. The automatic and manual versions are offset differently. If you try to install these gears onto an "Auto" diff it will never work.

Similar to this item

Red Line MT-90 GL-4 Manual Transmission Fluid - 1qt
Red Line MT-90 GL-4 Manual Transmission Fluid - 1qt
$12.98
Red Line MT-85 GL-4 Manual Transmission Gear Oil - 1qt
Red Line MT-85 GL-4 Manual Transmission Gear Oil - 1qt
$12.98
OEM Transmission / Differential Drain Plug Sealing Washer
OEM Transmission / Differential Drain Plug Sealing Washer
$3.19
Tomei Duracon Shift Knob
Tomei Duracon Shift Knob
$28
OEM Rear Differential Output Shaft Split Lock Washer
OEM Rear Differential Output Shaft Split Lock Washer
$1.01
CNC Aluminum Hub Centric Wheel Spacers 2.5, 5, 10, 15, & 20mm
CNC Aluminum Hub Centric Wheel Spacers 2.5, 5, 10, 15, & 20mm
$25