Product Description
Radiator hose sensor adapter is cast aluminum and fits into the upper radiator hose. Threaded with either 1/8" BSPT, 1/8" NPT or 3/8" NPT port to accommodate most aftermarket coolant temperature sensors.
Allows you to install a coolant temperature sending unit for an aftermarket gauge or a thermostatatic switch without having to drill and tap your existing metal pipes. Our design allows install into the curved portion of the upper radiator hose for a perfect fit. Simply cut and trim the upper radiator hose and install this adapter in-line. Includes the two additional clamps you'll need.
See options below to select the appropriate thread pitch. Autometer gauges and many thermostatatic switches have a sending unit with a 1/8" NPT (27) thread pitch. Most of the gauges and electronics made Japan including Defi, Greddy, Apex-i, HKS have sending units with a 1/8" BSPT (28) thread pitch. Spal Thermostatic Fan Switches sold here at Z1 are 3/8" NPT (18).
Measures an approximate 35mm (1.38'') in diameter.
*** This item does not qualify for any additional discounts or promotions *** |
 |
Z1 Stainless Steel Magnetic Oil Drain Plug
starstarstarstarstar (26)
$19.99
OEM 300ZX (Z32) Idle Air Gasket (IAA / IAC)
starstarstarstarstar_half (10)
$7.96
300ZX Non-Turbo Dual Electric Fan Setup
starstarstarstarstar_half (4)
$198
Z1 Silicone Upper Radiator Hose 300ZX Z32 (TT)
starstarstarstarstar (8)
$34
OEM Fuel Tank O-Ring
starstarstarstarstar (21)
$13.98
OEM Long Life Blue Coolant (Antifreeze) - 50/50 Pre-Mixed
starstarstarstarstar (53)
$18.89
Does this come with an insert or plug so that you can plug it off if you are getting a sensor at a later date?
It does not standard but if you need one just call in and one of our reps can sell you a plug with it to ship together.
Hi, I bought the z1 radiator hose kit and I want to buy one of these to fit a water temp sensor.
Firstly, which size one will I need considering I have the z1 silicone hoses?
Secondly, will I lose any coolant during the install, and if so should I just flush the system?
Richard,
This will work great with the Z1 Silicone hose. You will need to cut a section of the existing hose to make room for this adapter and you will more than likely loose a little coolant because you will have to cut that hose all the way through twice. Regards, Austin I.
Z1 Aluminum Coolant Bleeder Port - Heater Hose
starstarstarstarstar (178)
$34.99
Z1 Motorsports High Pressure Radiator Cap
starstarstarstarstar_half (99)
$29.99
Z1 G37 Silicone Master Hose Set
starstarstarstarstar_half (32)
$189.99
Z1 350Z / G35 VQ35DE Silicone Heater Hose Set
starstarstarstarstar_half (26)
$49.99
Z1 350Z / G35 VQ35DE Silicone Radiator Coolant Hoses
starstarstarstarstar_half (28)
$109.99
Z1 370Z / G37 Silicone Radiator Hose Set
starstarstarstarstar (25)
$99.99
starstarstarstarstar
Kevin
September 4, 2024
Great product very good quality
starstarstarstarstar
Adan
May 14, 2024
I install this in my girlfriend g35 and she loves it. Now she can see the temp of the car. I would definitely recommend it.
starstarstarstarstar_border
Paul
February 23, 2023
It is as advertised. You need one with two 1/8" npt holes
starstarstarstarstar
Jonathan
February 22, 2023
I have a temperature sender on the rear heater hose which is probably fine but this going directly in line from the engine to the radiator is going to give you accurate engine coolant temp.
starstarstarstarstar
DOUGLAS
November 27, 2022
11-27-22
Excellent quality according to my mechanic
starstarstarstarstar
Bud
October 26, 2022
Excellent quality, haven’t installed yet, but I’m sure it will fit like a glove!
Thank you
ASRIUBNFAIURNFKAJSNFLAKJSDNFLKASNDFLKASDNMFALKSNDFOANEF