Product Description
Subframe bushing collars take up slop developed because of old stock rubber subframe bushings, to yield a more responsive suspension and reduced wheel hop on aggressive launches. These 8 piece aluminum collars install above and below each of the four bushings and retain the stock anti-squat geometry, vs. 4 piece spacers that just install on the bottom slightly increasing anti-squat.
These collars are a great alternative to the considerable time and expense of actually replacing the entire subframe bushing, with similar results.
With age the stock fluid filled subframe bushings do not provide the necessary rigidity they had originally. We recommend this modification to tighten up the handling on any Z32.
Note: Top collar is slotted to allow installation without dropping the whole subframe.
Construction: CNC machined aluminum in your choice of Black or Silver finishes.
*** This item does not qualify for any additional discounts or promotions *** |
 |
check_circle_outlineAdded to cart
Please select and verify all product options for this bundle.
=
Energy Suspension Z32 Rear Differential Bushings
starstarstarstarstar_half (4)
$19.99
300ZX (Z32) Throttle Body Gaskets (Pair)
starstarstarstarstar (8)
$12
OEM 300ZX (Z32) Fuel Filter
starstarstarstarstar (17)
$21.20
OEM 300ZX (Z32) Oil Filter
starstarstarstarstar (11)
$6.47
300ZX (Z32) Upgraded Clutch Release Fork Assembly Kit
starstarstarstarstar (8)
$64.99
300ZX (Z32) Oil Filter
starstarstarstarstar (1)
$5.88
Hi There,
One of my rear subframe bushing I think it's start to worn out and leak a little bit fluid. do you think I could use this Collars set to fix the problem or I must need to drop the subframe and replace the bushing with aftermarket one?
Thanks,
Jack.
Jack,
No you do not need to remove the sub-frame. You just loosen it at all 4 corners to install the top collars, then one at a time remove the nut and washer from the bottom to install the lower collar. Install is quite easy.
Regards,
The Z1 Team
Z1 Urethane Rear Differential Bushing Set
starstarstarstarstar (156)
$79.99
Z1 Rear Differential Bushing Removal Tool
starstarstarstarstar_half (72)
$149.99
Z1 Offset Eccentric Bolt Elimination Kit
starstarstarstarstar_half (16)
$39.99
Z1 Q50 / Q60 Urethane Rear Differential Bushing Set
starstarstarstarstar (8)
$199.99
Z1 370Z / G37 Rear Subframe Tie Bar
starstarstarstarstar_half (8)
$89.99
Z1 350Z / G35 Rear Subframe Tie Bar
starstarstarstarstar_half (7)
$89.99
starstarstarstarstar
Gary
November 26, 2023
one of the bigger jobs I decided to do, but with a little thought and some work, these go in with reasonable ease ...jack stands, jacks etc...really only took a couple hours and I was moving slow and careful, No problem..but what a difference when you are done! No more tail wag! No more waiting for the tail to catch up, she's tight and right. Best performance handling mod for the money and time. Now I can feel the KYBs and lowering springs, I know what the car is going to do in a hard curve now...was a little iffy before ....and that leads to the ditch! Get thes and do it!
starstarstarstarstar
Ali
July 19, 2022
made so much difference the car is sharper on corners
starstarstarstarstar
Gregory
July 14, 2022
Look great and really helped reduce vibration from the rear. Installation was super easy thanks to the cut outs.
starstarstarstarstar
Ted
January 25, 2021
Very easy to install. Took about 45 minutes total. Previously the rear of the car would act slightly squirrelly when turning hard, especially when transitioning side to side. After installing the collars it tightened up.
ASRIUBNFAIURNFKAJSNFLAKJSDNFLKASNDFLKASDNMFALKSNDFOANEF